Results 1 to 6 of 6

Thread: For Hire Valve shimming tool.

  1. #1
    Join Date
    Nov 2007
    Location
    South Coast, NSW
    Posts
    870

    For Hire Valve shimming tool.

    Hi anyone out there with a 1hz cruiser will know that the valves require shimming checks to be done as part of regular maintenance routine. I checked mine recently and all the intake valves were out of tolerances. so i have bit the bullet and purchased the toyota genuine tool P/N: 09248-64011 that is required to remove and install the shims safely and without removing the cam. The tool was expensive as hell but im happy to hire it out to people for $20 + $100 deposit. I realise that it takes time for replacement shims take time to arrive from mr toyota so the loan period would be very reasonable eg 3 weeks.

    I hope you all stop putting off checking your valves and do it asap. To do the check all you need is a feeler gauge. and all u have to remove is the rocker cover. dead easy. My tool is only required if you find that your tolerances are out of spec.

    Contact me on
    0415509314
    Cheers Nick.
    Cheers
    Nick.
    Harold 2002 Toyota Landcruiser 105 series. 4.2lt turbo glide turbo, Too lazy to make bio nowdays times money. 3'' lift.

    Roidio 2001 Holden Rodeo 4x4 2.8L TD. 2.5" exhaust sytem, H/E shower system. 4" Lift, Airbags, And lots of fruit, B100 for 55,000 . SOLD

    Elsa 1983 Mercedes-Benz W123 300D. Still The Fastest Merc in Oz, Self built and Female proofed. COUSINS NOW

  2. #2
    Join Date
    Sep 2012
    Location
    Michigan
    Posts
    1

    Re: For Hire Valve shimming tool.

    Hi Nick

    I am willing to hire your tool for $20 +$100 deposit. Are you still renting Three weeks would be plenty.


    Kevin.

  3. #3
    Join Date
    Dec 2005
    Location
    Perth Western Australia
    Posts
    930

    Re: For Hire Valve shimming tool.

    Kevin,

    If you're serious, contact Nick on his mobile or via PM.

    Your profile says you're from Michigan, which is a long walk and swim from New South Wales.

    Tim
    Toyota Landcruiser 1988 HJ61 Manual Wagon
    12H-T turbo Direct Injection.
    Twin Tank setup runs on 100% WVO after warm up. 30 plate FPHE with 80C output, 12mm fuel lines
    Start up and shut down electric fuel pump feeds IP direct.
    Front 4WDSytstems Lokka, Rear ARB airlokka for quick escapes up sandhills. Performance GTurbo with 600mm FMIC gives 450nm @ 1700rpm at 20psi boost.

  4. #4
    Join Date
    Jan 2006
    Location
    In the sunshine state.
    Posts
    851

    Re: For Hire Valve shimming tool.

    Kevin,

    Some assistance can be found here

    LCOOL.org :: Log in

    Not sure if you have to join to see it though, its easy to join and you will find lots of info for your 1HZ

    Matt
    Biodiesel Bandit

    Landcruiser '98 80 series B100.

  5. #5
    Join Date
    Nov 2007
    Location
    South Coast, NSW
    Posts
    870

    Re: For Hire Valve shimming tool.

    Tool hire is on hold as i live in the UK now sorry. Seriously though 1 hz guys check your clearances.
    Cheers
    Nick.
    Harold 2002 Toyota Landcruiser 105 series. 4.2lt turbo glide turbo, Too lazy to make bio nowdays times money. 3'' lift.

    Roidio 2001 Holden Rodeo 4x4 2.8L TD. 2.5" exhaust sytem, H/E shower system. 4" Lift, Airbags, And lots of fruit, B100 for 55,000 . SOLD

    Elsa 1983 Mercedes-Benz W123 300D. Still The Fastest Merc in Oz, Self built and Female proofed. COUSINS NOW

  6. #6
    Join Date
    Jun 2017
    Location
    Oxford, UK
    Posts
    1

    Re: For Hire Valve shimming tool.

    Hi Nick, are you still in the UK? I could do with the loan of this valve shim tool please! Cheers mate, Bud 07890351454

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •